trimmer-yd2333云顶电子游戏

wheel equipment wheel mold car mould car parts intelligent temperature measurement access with face recognition:

trimmer-planisher-end cutting

this machine is composed of trimmer, planisher and end cutting unit, which of trimmer is special equipment of steel wheel production for removing and trimming welding slag generated by wheel rim welding to obtain flat welding seam surface. planisher machine is used to flatten and strengthen the welded seam after welding slag planishing and trimming. end cutting machine is used for cutting the both ends of redundant welding materials of welding seam, cutting action drives by oil cylinder.

详细描述

summary

this machine is composed of trimmer, planisher and end cutting unit, which of trimmer is special equipment of steel wheel production for removing and trimming welding slag generated by wheel rim welding to obtain flat welding seam surface. planisher machine is used to flatten and strengthen the welded seam after welding slag planishing and trimming. end cutting machine is used for cutting the both ends of redundant welding materials of welding seam, cutting action drives by oil cylinder.


specification/description data

model numberbgq-300-ah
rated input voltageac380v,3phsae
rated input frequency50hz
rated input capacity37kva
max. thickness of rim5mm
width range of rim220-320mm
diameter range of rimφ280~φ450mm
maximum clamping force of trimmer6tons
maximum trimming force6tons
maximum clamping force of planisher6tons
maximum rolling force of planisher6tons
maximum cutting force of end-cutting18tons
diameter of cutting oil cylinder of end-cutting160mm
system pressure12mpa


trimmer unit

刨渣机是车轮生产中用于除去轮辋焊接后产生的焊渣,从而得到平整的焊缝表面。该机设计为自动操作,由主机、液压系统和电气系统等组成.其中液压系统和电气系统与滚压机、端切机共用。

planning machine is special equipment of steel wheel production for removing and trimming welding slag generated by wheel rim welding so as to obtain flat welding seam surface. the machine is designed as automatically operation, it consists of host, hydraulic system and electric system, wherein hydraulic system and electric system are shared with rolling press machine and end cutting machine.

/lathe bed

host frame is c-type mechanism. the hydraulic driven clamp holder clamps two sides of welding seam.

/clamping mechanism

work piece is clamped and fixed by hydraulic clamping mechanism, and the mechanism is installed on the upward side of guide rail. the stop block is installed on clamping jaw to avoid axial loosening of work piece during slag planning.

the clamping mechanism is divided into two parts, the lower part of which is fixed on the lathe bed of frame, the upper part is movable and driven by oil cylinder.

/trimming mechanism

upper and lower slag planning cutter is installed on steel sliding frame. the sliding frame makes to-and-fro movement in the middle of clamp holder by support of guide rail after hardening treatment, and cutting surface of each cutter is set manually according to material thickness.

cutting surface and clamp holder of slag planning cutter are connected by one set of mechanic mechanism to ensure its relative position. therefore, whatever any material thickness, the machine will not set each time, and can cut material with difference thickness automatically.

three cutters are installed on sliding frame, and lower clamp holder uses fixed-type, and is also used as guide rail of lower sliding frame. movement of upper and lower cutters is driven by hydraulic cylinder.

/clamping mechanism

work piece is clamped and fixed by hydraulic clamping mechanism, and the mechanism is installed on the upward side of guide rail. the stop block is installed on clamping jaw to avoid axial loosening of work piece during slag planning.

the clamping mechanism is divided into two parts, the lower part of which is fixed on the lathe bed of frame, the upper part is movable and driven by oil cylinder.

/trimming mechanism

upper and lower slag planning cutter is installed on steel sliding frame. the sliding frame makes to-and-fro movement in the middle of clamp holder by support of guide rail after hardening treatment, and cutting surface of each cutter is set manually according to material thickness.

cutting surface and clamp holder of slag planning cutter are connected by one set of mechanic mechanism to ensure its relative position. therefore, whatever any material thickness, the machine will not set each time, and can cut material with difference thickness automatically.

three cutters are installed on sliding frame, and lower clamp holder uses fixed-type, and is also used as guide rail of lower sliding frame. movement of upper and lower cutters is driven by hydraulic cylinder.


planisher unit

the planishing machine is use to flatten and strengthen the trimmed welding-seam, the planisher's main parts includes machine, movable c-type frame, clamping device, rollers and hydraulic parts. c-type frame equipped with hydraulic drive system for rolling roller that fixed on the clamping mechanism.

/c-type frame

c-type frame fixed on the holder that can move along with the guide rail, it will be driven by oil cylinder. holder can slide through roller bearing that set four (4) roller bearings each side. c-type frame's main function is to prevent rolling pressure skewing and the resulting rolling press size deviation.


end cutting unit

/lathe bed

c-type frame supports all major components and it is convenient for operation and adjustment.

oil cylinder fixed on the top of the c-type frame which is used to drive the clamping and cutting mechanism, and it can be adjusted according to the width of rim band, the hand wheel adjusting mechanism mounted on the tail of frame.


/cutting mechanism

cutting mechanism cuts the both end of welding slag by cutting tool. the upper tool drives by high-pressure oil cylinder that stroke is 60 mm, upper tool (cutter) and lower tool (cutter) connects together by the linear guide pillar and guide sleeve. the front of the cutting tool (upper and lower) fixed on the upper and lower tool base, the back of the cutting tools installed on the movable slide base which can be adjusted according to workpiece width.

cutting tools (cutter) made by tool steel, each pair cutter includes convex and concave shape tool, complete material cutting quickly. the clearance of upper and lower cutting tool should be 8-10% of the material thickness, for achieving the standard workpiece size at 0.2 mm.

note: the clearance should be checked after cutting tool adjusting finished!

/ hand wheel adjuster

hand wheel adjuster can adjust the sliding seat position to adapt the width change of work pieces, including air cylinder, the tailstock and cutting tools, sliding seat can move horizontally by the hand wheel at the back of frame.


cooling unit

the cooling unit is driven by the air pressure and designed as lever structure. inside upper and lower cooling cooper band has cooling water circulation.


鲁icp备090054547号-1 | © 2018 shandong xiaoya jinggong machinery co., ltd.


sweep learn more

zip code: 250000

address: no. 51, industrial south road, jinan city, shandong province

international trade department: 0531-83122188

email: xiaoyatooling@163.com

400-6586-222

网站地图