冲气门孔机-yd2333云顶电子游戏

用途和特点/purpose and features

本机是为中、重无内胎车轮轮辋压平面、冲气门孔设计的专用双动液压机。

本机分为主机、动力机构和电气控制箱三大部分，具有独立的液压传动装置和电气控制箱。

采用plc控制，可以实现手动调整、自动二种操作规范，并具有超温保护、紧急停车、过滤器堵塞发讯等功能。this machine is a kind of special double-action hydraulic press which is used for valve hole flattening and punching of medium & heavy duty commercial vehicle rim.

this machine is composed of host device, hydraulic driving device and electrical cabinet.

its operation can be controlled by plc system which can switch between auto and manual, and has multiple functions including over temperature protection, emergency stop, filter clogging alarm and so on.

its operating pressure, working speed and stroke range can be adjusted according to the requirements of technology and processing.

its host device’s slider mounted 2 guide way which used for guiding, and the 2 guide way can bear eccentric force when slider suffer eccentric load, to avoid direct effect on the piston rod, to prevent the eccentric wear and strain of piston rod, so this design can increase service life of seal.

本机的工作压力、工作速度、行程范围等可根据工艺需要进行调节。

本机滑块有二根导轨进行导向，当滑块受偏心载荷时，由二根导轨承受，避免直接作用在活塞杆上，防止活塞杆的偏心磨损和拉伤，提高密封寿命。

技术参数/specification

设备型号	model number	ykq-400-ah
压平油缸公称力	nominal press force of flattening cylinder	630kn (p=25mpa)
滑块最大行程(可调)	maximum travel of flattening slider	320mm, adjustable
冲孔油缸公称力	nominal press force of punching hole	320kn (p=20mpa)
冲孔油缸最大行程	maximum travel of punching cylinder	25mm
滑块至工作面最大距离	max. distance between slider undersurface and working table surface	670mm
滑块尺寸	slider size	300mm×200mm
喉深	throat depth	225mm
工作台尺寸	working table size	w650mm×d635mm
工作台到地面高度	vertical height from working table to floor	750mm
滑块快速下行速度	fast downward speed of slider	80mm/s
滑块慢速工作下行速度	lower downward speed of slider	43mm/s ~ 17mm/s
滑块回程速度	return speed of slider	90mm/s
液压电机功率	hydraulic motor power	18.5kw

本机由主机、液压传动装置和电器控制装置三个部分组成，主机包括：机身、主缸。液压传动装置包括油箱、油泵—电机组、集成阀等，电气装置包括电气控制箱、电气操纵箱等。主机和液压传动装置安装在混凝土基础上，基础见附图所示，电气箱安放在机身后面

the valve hole press machine consists of three parts: main machine, hydraulic transmission device, electrical control device. the main machine includes: lathe bed, main cylinder. hydraulic transmission device includes oil tank, oil pump-motor group, pile-up valve etc. electrical device includes electrical control box, electrical operation box etc. the main machine and hydraulic transmission device are installed on concrete foundation, which is shown on attached drawing. the electrical box is installed on back of lathe bed.